Speaker Bar System
SP-SB23W
RegisteR youR pRoduct at:
Protect Your New Investment
The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
Improve Product Development
Your input helps us continue to design products that meet your needs.
Operating Instructions
3
English
4
English
5
English
PrODUCt DISPOSal
if this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures: Reorient or relocate
the receiving antenna. increase the separation between
the equipment and receiver. connect the equipment
into an outlet on a circuit different from that to which
the receiver is connected. consult the dealer or an
experienced radio/tV technician for help.
certain international, national and/or local laws and/
or regulations may apply regarding the disposal of
this product. For further detailed information, please
contact the retailer where you purchased this product
or the in your country.
NOTE: this equipment has been tested and found to
comply with the limits for a class B digital device,
pursuant to part 15 of the Fcc Rules. these limits are
designed to provide reasonable protection against
harmful interference in a residential installation. this
equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
• the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least
20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna
or transmitter.
• changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
PleaSe take INVeNtOrY
please check to ensure you have everything in your pioneer sp-sB23W speaker Bar system carton.
inside, you should find:
SPeaker Bar
POwer COrD (x2)
SUBwOOfer
6’ DIgItal (OPtICal) CaBle (1)
remOte CONtrOl
(BatterY INClUDeD)
rUBBer feet fOr SPeaker Bar (x2)
6
English
Owner’s Manual
ImPOrTANT NOTE: if anything is missing or damaged, or if your new pioneer sp-sB23W speaker Bar system
fails to operate, please notify your dealer immediately. We recommend keeping your original carton and packing
materials in case you need to ship the unit in the future.
about Your SP-SB23w
Speaker Bar System
Bluetooth® wireless technology allows for playback
of music from your smartphone, tablet or other
compatible device.
thank you for choosing the sp-sB23W speaker Bar
system from pioneer electronics. please read through
this owner’s Manual before using your speaker Bar
system to optimize performance. after you have
finished reading this owner’s Manual, store it in a
safe place for future reference.
Learning mode enables you to use your favorite
remote to control the functions of your speaker Bar.
Like every subwoofer we build, this wireless
subwoofer is engineered to offer incredible design
and amazing low-end frequency sound quality,
ideal for music and movies.
the speaker Bar utilizes technology and components
derived from our award-winning home theater speakers,
with a primary goal of producing the most immersive,
natural, and room filling sound experience for both
movies and music.
this speaker Bar provides dolby® digital decoding,
the standard for high definition sound.
the curved wood cabinetry houses six speakers,
individually amplified, for the best audio experience.
utilizing a three-way active crossover network, the
speaker bar delivers a tailored response for all your
favorite sources.
Bar CONtrOlS (Front panel)
1. Power—turns on the bar or puts it in standby mode.
2. Volume Up and Down ( + / - ) —adjusts the volume
of the speaker Bar.
3. Source—changes which input source you are
listening to.
Source 1: analog. Led color will be a steady Blue.
1.
2.
3.
Source 2: digital/optical. Led color will be a steady
Blue.
4.
5.
Source 3: Bluetooth: Bluetooth® wireless technology
(see “paiR aNd coNNect youR BLuetootH
deVice” on page 10) Led color will be a steady Blue.
PLEASE NOTE: only one source connection will be
active during use of the speaker Bar system.
4. listening mode (second Row Left)
Music
Movie
dialogue
5. BlUetOOth/PaIrINg/learN (second Row Right)
SPeaker Bar POwer INDICatOr
powering up:
SOUrCe leD
Blue Solid—Movies preset. ideal for special effects
and movie soundtracks.
Blue Steady—power is on; all is well.
red Solid—Music preset. ideal bass balance for the
most natural music reproduction.
No lights—Main power switch is off or the
speaker bar is in standby mode.
green Solid—dialogue preset. ideal for late night viewing or
Blue Slow Blinking—system is muted.
dialogue heavy content. in this mode, the subwoofer is inactive.
7
English
Bar CONtrOlS (Back panel)
3.
4. 2.
1.
5.
1. Power Connection—the bar power cord
SUBwOOfer CONtrOlS (Rear panel)
connects here.
subwoofer power Led
2. SYNC—the syNc button ensures the subwoofer
and bar are communicating. (see “HoW to paiR
youR suBWooFeR to tHe speakeR BaR”
on page 8.)
red Steady—the subwoofer is plugged
in/in standby mode.
green Steady—the subwoofer is on and
producing sound.
3. analog Input—allows for the connection of most
legacy audio devices.
subwoofer sync Led
4. Optical Input—allows for the connection of digital
audio from modern electronics such as tV's, disc
players, cable Boxes, and satellite Boxes.
Blue flashing—the subwoofer is searching
for the speaker bar.
Blue Steady—the subwoofer and speaker
bar are synced.
5. Power Switch — Main power switch for the
speaker Bar.
remOte CONtrOl
1. Power ( )—turns on the bar or puts it in
1.
2.
standby mode.
2. Source 1, 2, 3—changes which input source
4.
3.
5.
3.
you are listening to.
3. Volume Up and Down ( + / - ) —adjusts the
master volume of the system.
4. mute—Mutes and unmutes the audio coming
from the speaker bar and subwoofer.
5. Bluetooth®—track Forward, play, pause,
6.
7.
track Backward.
6. SUB Volume Up and Down ( + / - ) —adjusts
the volume of the subwoofer
7. mode—Music, Movie, dialogue.
8
English
hOw tO CONNeCt YOUr SPeaker Bar aND
SUBwOOfer tO YOUr tV
the simplest approach is to connect the optical audio output of your tV to the optical input on the
back of the bar. this method will provide the highest quality audio. if your tV does not have an optical
output, you can use the optical output from your dVd player or your cable/satellite box to connect to
the optical input on the bar or use an analog cable (Not supplied).
hOw tO PaIr YOUr SUBwOOfer tO the SPeaker Bar
Make sure that both the speaker Bar and
subwoofer are plugged into an ac outlet.
speaker Bar
1. power on the speaker bar.
2. press and hold the sync button on the rear of
the speaker Bar until the sync Led begins to
flash red rapidly.
3. press and hold the sync button on the rear of the
subwoofer until the blue Led begins to flash rapidly.
4. after a couple of seconds both sync Leds should
become solid.
subwoofer
5. if the Leds continue to blink then move the
subwoofer closer to the speaker Bar.
CONCerNINg the PlaCemeNt Of thIS SYStem
USINg the rUBBer feet wIth the SPeaker Bar
CAuTION
included in the sp-sB23W speaker Bar carton are
(2) feet for the speaker bar to rest on. place the
feet at the desired location of the speaker. they can
be spaced a variety of widths apart for installation
flexibility. once placed on the feet, tilt the speaker to
the desired angle, depending on the location of the
speaker in relation to the desired listening position.
When assembling the system, lay them down flat on
their side to avoid accidents or injury. Make sure to
use a stable surface when assembling, setting up,
and placing the system.
WHErE TO LOCATE YOur BAr FOr THE BEST SOuND
correct placement is important for maximizing the sound
quality of your speaker Bar. take time to experiment
with positioning according to these guidelines.
the speaker bar may be positioned above or below
the tV. For best results align the front of the speaker
bar with the front of the tV.
At least 20"apart
due to the well-controlled vertical directivity, it is not
normally necessary to vertically aim the loudspeaker
towards the listener. if, however, the speaker bar is
placed under the tV and very close to the floor, then
tilting upwards may be beneficial.
NOTE: spacing between the rub-
ber feet should be at least
20 inches apart to avoid the
speaker Bar from tipping over.
to achieve optimum audio performance, place the
main unit beneath the television monitor.
NOTE: do not use adhesive or
screws to attach the feet to the
speaker. doing this will damage
the cabinet and void the warranty.
9
English
wall mOUNtINg the SPeaker Bar
PlaCemeNt aND fINe tUNINg
THE mAIN uNIT CAN BE mOuNTED ON A WALL IF
DESIrED. IF YOur TV IS WALL mOuNTED, THE BAr
CAN mOuNT rIgHT BENEATH IT. THE BAr HAS
BuILT-IN kEYHOLE SLOTS THAT mAkE IT EASY.
the subwoofer receives its audio signals wirelessly
from the main unit, so it requires no speaker cables,
allowing you to place it in the most convenient location
(a power cord connection is required, however).
the placement of your new subwoofer is critical to its
performance. the two of the most common locations
include:
a) in the corner of the room (which can result in a
boomy or exaggerated low frequency response),
B) placement along one wall but out of the corner
(moderate bass performance with increased fidelity
over corner placement.
experimentation with subwoofer placement is highly
encouraged, as slight adjustments can create large
benefits in sound reproduction. to further test subwoofer
placement, install the subwoofer temporarily in your
main listening position and while playing a familiar
piece of music, walk around the listening room until
you find the best sounding position. this is a possible
location for the subwoofer to be placed.
CAuTION
Pioneer recommends that you consult a installation
professional for wall mounting the speaker bar.
ImPOrtaNt
pRecautioNs RegaRdiNg suBWooFeR
iNstaLLatioN:
• When the speaker Bar is mounted to a wall, there is
a risk of it dropping, falling, etc. due to the weight or
mounting method. take sufficient care not to cause
an accident.
• sound from the subwoofer may be interrupted due to
poor signal conditions, but this is not a malfunction.
if it occurs, rearrange the position and orientation of
the main unit and/or subwoofer as required.
• select a location for installation/mounting with
sufficient strength to withstand the weight. if you are
unsure of the strength or anything else, consult with
a professional.
• the subwoofer is designed to be used within a distance
of 10 m (32 ft.) from the main unit. the actual distance
within which it can be used, however, may be less,
depending on the environment and design of the
room where it is used.
• pioneer is not responsible for any accidents or
damage that result from improper installation/
mounting, incorrect use, modification, disaster, etc.
• do not hang from the unit. pay special attention
to children. the unit may fall and break, resulting
in injury.
• signal reception by the subwoofer may be unstable
if it is placed too close to the main unit. in this case,
separate the subwoofer at least 1 m (3.2 ft.) from
the main unit.
• do not connect or disconnect the cables while the
unit is mounted to the wall. install the cables in
such a way that a foot or other object cannot get
caught in them.
• signal reception by the subwoofer may be interrupted
if an obstruction (metal door or concrete wall, aluminum
covered insulation, etc.) is placed between it and
the main unit. in this case, install the subwoofer in
an uninterrupted line-of-sight orientation from the
main unit.
CaBINet maINteNaNCe
great care and craftsmanship has gone into the
construction and finish of the cabinet. periodically
use a soft, dry cloth to remove dust or fingerprints.
do not use paper towels or other abrasive materials
as it may damage the finish.
NOTE: please retain the carton and packing material
for your pioneer products, to protect them in the event
of a move or if they need to be shipped to a service
center. product received damaged by a service center
that has been shipped by the end user in other than
the original packaging will be repaired, refurbished
and properly packaged for return shipment, at the end
user’s expense.
where tO lOCate YOUr SUBwOOfer
fOr the BeSt SOUND
your wireless subwoofer is really easy to place and
can go just about anywhere in the room. plus you
don’t have to worry about connecting wires, because
the only wire you have to plug in is the power cord.
10
English
BlUetOOth wIreleSS teChNOlOgY
teaChINg YOUr SPeaker Bar tO reSPOND tO
aNOther remOte CONtrOl
to use your Bluetooth® wireless technology device
with the sp-sB23W speaker Bar system, you must
first pair your device with your speaker Bar.
PrOgrAmmINg INSTruCTIONS: your speaker bar
is currently programmed to respond to the remote
control that is included with the product. However, we
strongly recommend programming the speaker bar to
also respond to your existing remote control using the
steps illustrated below. this will enable you to operate
all of your components using a single remote control.
While programming the speaker bar, ignore anything
that may be displayed on the tV screen.
pairing creates the ability for your Bluetooth® device
to connect with your speaker Bar wirelessly and
exchange information.
you only have to pair your speaker Bar with your
Bluetooth® device one time for this exchange of
information to take place.
Not all remote controls can be used to control the
PaIr aND CONNeCt YOUr BlUetOOth DeVICe
Speaker Bar.
1. Make sure your Bluetooth® device and speaker
Bar are powered on and the Bluetooth® source
is selected on the speaker bar (Blue light above
Bluetooth® logo is solid blue).
2. activate the Bluetooth® function on your
Bluetooth® source device and check it is actively
looking for a Bluetooth® device.
3. press and hold the Bluetooth® pairing button until
the Bluetooth® light begins to flash slowly.
4. your speaker bar will now appear on your
Bluetooth® source device. select “sp-sB23W” on
your Bluetooth® device to initiate pairing.
1. power on the speaker Bar and wait for the blue
5. after a few seconds your speaker Bar will now be
paired with your Bluetooth® device and you can
enjoy music playback wirelessly. Note: only one
device can be connected to the speaker Bar at
one time.
light to become solid.
2. using the souRce button select either analog or
digital input.
3. press and hold the speaker Bar's BLuetootH/
paiRiNg/LeaRNiNg button until the Bluetooth®
light flashes. Release the button. the light will now
turn solid blue.
6. using the included remote for your speaker Bar,
you can track forward and back, pause and play
your current track, and turn the Volume up and
down.
4. press the button on the speaker Bar that you
would like to teach, the Bluetooth® light should
begin to flash slowly.
5. point the remote control that you want to use for
your speaker bar and push the corresponding
command button that you chose in step 4.
1'- 2'
aUtOmatIC CONNeCtION
any time you want to connect the last paired device
and play it through the speaker bar, do the following:
1. turn your device’s Bluetooth® function on.
2. enter Bluetooth® source by pressing the Bluetooth®
source button from the remote.
NOTE: By default, the last connected Bluetooth®
6. the Bluetooth® light should begin flashing quickly
and the mode light will flash green if the code
was accepted (if the mode light flashes red the
code was not accepted. Move the remote control
closer and push the button again). Now push your
remote's command button again and if the mode
light flashes green the command is now set.
device will automatically connect if available.
hOw tO DISCONNeCt wIth a BlUetOOth DeVICe
7. Repeat this process for each button you would like
turn off or disconnect the Bluetooth® feature on your
to teach your speaker bar.
Bluetooth® device.
8. to exit the learning mode press and hold the
BLuetootH/paiRiNg/LeaRN button until the
Bluetooth® flashes. then release the button. the
Bluetooth® light is now off.
Not all features are available on all Bluetooth
source devices.
11
English
hOw tO OPtImIZe the SOUND wheN
use the following steps to adjust the volume balance
tV SPeakerS are ON
between your tV and the bar:
1. if necessary, program your bar to respond to the
volume up and down control commands of your
tV remote.
you should hear sound from the bar. if you don’t, turn
up the volume on the bar using its volume control but-
tons. if your bar is connected to your tV, there’s a very
good chance your tV speakers are also playing. it’s
impossible to give specific instructions on how to turn
off the speakers for every tV, but here’s a way to do it
that covers many of the tVs out there.
2. turn your tV volume all the way down using the
control buttons on your tV.
3. then, using the volume keys on your speaker
bar set the volume to a normal listening level
(do not use the remote control). after you make
these adjustments, your speaker bar should
always be louder than your tV speakers.
then use the tV remote control to adjust the
volume as you normally do.
1. on your tV remote control, find a “menu”
or “setup” button.
2. press this button. you should see an
on-screen menu.
3. Next, look for an option to control audio
functions and select it.
CUStOmer SerVICe/teChNICal SUPPOrt:
For assistance with basic set up, operation,
or troubleshooting, you may contact our
customer service hotline at:
the setting to turn off your tV’s internal speakers should
be here. if you can’t turn off your tV internal speakers,
don’t worry. to enjoy the best performance from your
bar, you’ll want it to play louder than your tV.
1 (800) 421-1404
Hours: Monday-Friday10:30 am-7:00 pm est
speakeR BaR
dimensions
cabinet
35.98" W x 4.05" H x 4.74" d
caRB2 MdF Wood
Finish
Black ash Vinyl
Frequency Range
drivers: Mid-Woofer
drivers: tweeter
45Hz - 20kHz
3" x 4 (2 per side)
1" x 2 (1 per side)
power output
6 x 28 Watts (1kHz 1% tHd @ 4 ohms)
toslink optical x 1, analog x 1
a2dp Wireless 2.4 gHz
100v - 240v
inputs
Bluetooth®
Voltage inputs
power consumption
power consumption (standby)
power consumption (Main power switch off)
60 Watts
2 Watts power off/4 Watts auto power off
0 Watts
suBWooFeR
dimensions
cabinet
9.01" W x 10.01" H x 9.01" d
caRB2 MdF Wood
Black ash Vinyl
Finish
driver
6.5" Woofer
Voltage input
100v-240v
power output
power consumption
power consumption (standby)
50 Watts (50Hz 1% tHd @ 6 ohms)
60 Watts
1 Watt
|