Unpack and Inspect
Setup
3
4
5
6
7
Attach Label Stock
Operation
Specifications
511279-120110
© 2010 All rights reserved
Section 1: Unpack and Inspect
Thank you for purchasing the RW-12. The RW-12 Label Rewinder makes it easy to
rewind large quantities of labels. Its perfect for use with Primera’s entire line of LX-
Series Label Printers and many other label printers.
Adjustable Label Guide
Fixed Label Guide
Chuck
Chuck Tension Knob
Chuck Support Bar
Dancer Arm
2 Amp Fuse
Speed Control
Power input
Power Switch
3
Section 2: Setup
The RW-12 Rewinder is fully assembled inside the box. However, to get started you will
need to plug in the power cable, switch the unit on and install the stability stand. Please
follow the instructions below to install the stability stand.
1. Remove two thumb screws on the base of the unit.
2. Attach the stand to the base.
3. Reattach the Thumb Screws.
4
Section 3: Attach Label Stock
1. Locate a suitable core on which to rewind labels. The core should be equal to or
less than the width of the liner width.
2. Remove the Chuck Support Bar by unscrewing the thumb screw at the base.
3. Place the core on the chuck.
4. Place the Adjustable Label Guide on the chuck. Push it tight against the core.
5. Tighten the Chuck Tension Knob so that the core and the guides do not move.
6. Reattach the Chuck Guide Bar to the base with the thumb screw.
7. Set the printer on the stability stand. Follow these guidelines:
• The feet of the printer should set anywhere on the lower portion of the stand.
• Line up the edge of the labels exiting the printer with the Fixed Label Guide on
the rewinder by moving the printer from side to side.
• The distance from the printer output to core is adjustable according to user
preference. Start with the front of the printer in the middle of the lower portion of
the stand.
5
8. Before you attach the label stock print a header of approximately 2 feet (61 cm) of
label stock.
9. Feed the header under the dancer arm.
10. Attach the stock to the core using tape.
11. Turn on the rewinder.
12. Start your print job.
Section 4: Operation
During normal operation the following will occur.
1. When the dancer arm is in a central position, the unit is idle;
2. When the dancer arm is down, the unit rewinds the labels onto the core;
3. When the tension arm is up, the unit unwinds the labels;
During a job the rewinder will primarily switch between operation 1 and 2.
LX900 Users: Approximately every 5 labels the LX900 printer pulls labels back into the
printer. In this case the dancer arm will go up and the labels will temporarily unwind
back toward the printer. This operation is normal.
End of roll: When the printer and rewinder reaches the end of the roll the rewinder
winds the remaining labels onto the core and the dancer arm will contact the base. This
will cause the rewinder to stop. The rewinder will sound an acoustic signal when the roll
is finish.
Speed Control: Depending the speed/quality of the print you may need to decrease or
increase the speed of the rewinder. Increase the speed if the rewind operation can not
keep up with the printing. Decrease the speed if the dancer arm seems to be jerking up
and down as it rewinds labels.
6
Section 5: Specifications
Maximum Roll Diameter:
Core Size:
10” (254 mm)
3”
Maximum Roll Width:
Minimum Roll Width:
Electrical Rating:
Power Input:
8.5” (216 mm)
1” (25.4 mm)
29V, 2.5 A
100-240 VAC, 50/60 Hz
17 lbs (7.7 kg)
Weight:
Dimensions:
17.5”W x 6.5”D x 13.5”H
(444.5mm x 165.1mm x 342.9mm)
7
|
Peerless Industries TV Mount MM746PU User Manual
Philips Car Stereo System CEM1100 User Manual
Philips Car Video System 19SI User Manual
Pioneer Computer Drive DE UH9101 User Manual
Pioneer DVD Player DV 989AVi S User Manual
Pioneer Stereo Receiver D2000SPL User Manual
Pitney Bowes Scale G799 User Manual
Planar Projector TD3200 User Manual
Polaroid Portable DVD Player PDV 0823A User Manual
Power Acoustik Car Amplifier PS1 2000D User Manual